Authentic NFPA Certification Exam CFPS Questions Answers

According to NFPA 230: Standard for the Fire Protection of Storage, 2015 Edition, building codes should limit the size of an unsprinklered facility used for the processing and storage of Municipal Solid Waste (MSW) built of type V construction to 7,500 ft2 (697 m2). This is based on the assumption that the MSW has a heat release rate of 18,000 Btu/ft2-min (200 kW/m2) and a fire growth rate of 0.046 min-1.Type V construction is defined as a type of construction in which the structural elements, exterior walls, and interior walls are of any materials permitted by the code123

References:

• NFPA 230: Standard for the Fire Protection of Storage
• 5 Types of Construction per the IBC | Building Code Trainer
• 2.4 MUNICIPAL SOLID WASTE LANDFILLS - U.S. Environmental Protection Agency

The answer is C. Human factor plays a significant role in most industrial fire and explosion losses.According to a study by Allianz Global Corporate & Specialty (AGCS), human error is the cause of 80% of all industrial accidents, including fires and explosions1. Human error can include mistakes, negligence, violations, or sabotage. Some examples of human errors that can lead to fires and explosions are:

• Improper handling or storage of flammable or combustible materials
• Failure to follow safety procedures or regulations
• Lack of training or supervision
• Poor maintenance or inspection of equipment or machinery
• Ignoring or disabling alarms or warning systems
• Smoking or using open flames near hazardous areas
• Intentional or accidental ignition of explosives or incendiaries

To prevent or reduce the impact of human errors, industrial facilities should implement effective risk management strategies, such as:

• Providing regular and adequate training and education for workers and managers
• Establishing and enforcing clear and consistent safety policies and rules
• Conducting thorough and frequent audits and inspections
• Installing and maintaining reliable fire protection systems and equipment
• Developing and practicing emergency response and evacuation plans
• Encouraging a positive safety culture and communication among all stakeholders

valve at the inspector’s test connection.

For wet-pipe automatic sprinkler systems, the only proper way to test the operation of a vane-type water flow alarm initiating device is to open the valve at the inspector’s test connection. This is a small valve that is located at the end of a pipe that is connected to the sprinkler system, usually at the most remote or highest point. The inspector’s test connection simulates the flow of a single sprinkler head and activates the vane-type water flow switch, which in turn triggers the fire alarm panel and the external alarm devices.Opening the valve at the inspector’s test connection also allows the water to drain from the system, preventing corrosion and freezing1234

Opening the main (2 in. diameter) drain is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not create enough flow to activate the switch. The main drain is used to drain the entire sprinkler system for maintenance or repair purposes, and it is usually located at the main riser or the fire department connection.Opening the main drain may also cause a pressure drop in the system, which could affect the performance of the sprinklers1234

Opening the alarm test by-pass valve at the system’s main riser is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not simulate the actual flow of a sprinkler head. The alarm test by-pass valve is used to test the operation of the external alarm devices, such as the water motor gong or the electric bell, without activating the fire alarm panel. The alarm test by-pass valve is usually located near the alarm check valve or the water flow switch, and it allows water to flow through a small orifice to the alarm devices.Opening the alarm test by-pass valve does not create enough flow to activate the vane-type water flow switch1234

Opening the check valve from the city connection is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not create any flow in the sprinkler system. The check valve from the city connection is used to prevent the backflow of water from the sprinkler system to the city water supply, and it is usually located at the fire department connection or the main riser.Opening the check valve from the city connection does not affect the water flow in the sprinkler system, and it does not activate the vane-type water flow switch1234

References:

• Fire Sprinkler Flow Switch & Tamper Switch Inspection & Maintenance3
• Sprinkler System Water Flow Device Testing - ORR Protection2
• VSR-AT Auto-Test Waterflow Alarm Switch | Potter Electric4
• WFDNA Series Vane-type Waterflow Detectors - Steel Fire Equipment5