300-110 Exam Dumps - Cisco CCNP Wireless Questions and Answers

This WGB (Workgroup Bridge) design scenario requires satisfying multiple simultaneous constraints. EAP-FAST (Flexible Authentication via Secure Tunneling) is the correct authentication protocol because it provides enterprise-grade 802.1X security using protected access credentials (PAC) without requiring a certificate to be installed on each AP or WGB device — directly satisfying the enterprise-grade security without certificates requirement. EAP-TLS (Options B and D) requires client certificates on every authenticating device, which is explicitly excluded. Mobile station mode is required rather than static mode (Options C and D) because mobile station mode enables the WGB to aggressively scan and roam to optimal mesh neighbors dynamically, evaluating neighbor signal quality and switching to better RAPs/MAPs as the truck moves along its path. Static mode fixes the WGB to a specific channel or AP, preventing the aggressive scanning and roaming required for the latency-sensitive application. The dot1q-capable switch connection supports multiple clients in different VLANs via 802.1Q VLAN tagging between the WGB and the truck ' s local network switch. Reference: WLSD Study Guide — Workgroup Bridge Design, EAP-FAST Authentication, Mobile vs. Static WGB Mode, Industrial Wireless Design.

Configuring a high availability SSO pair on Cisco Catalyst 9800 IOS XE WLCs has specific technical prerequisites that must be satisfied for the SSO relationship to form and function correctly. The two critical requirements are: each WLC must have a unique Redundancy Management Interface (RMI) IP address (Option B), and both WLCs must run identical IOS XE software versions (Option D). The Redundancy Management Interface is the dedicated in-band control channel over which the active and standby WLCs exchange state synchronization information, keepalive messages, and configuration updates. Each controller requires its own unique RMI IP address within the same subnet — the active uses one address and the standby uses another. If they shared the same RMI IP (Option C), there would be an IP address conflict preventing the interface from functioning. Identical software versions (Option D) are mandatory because the SSO state synchronization protocol and data structures must be version-compatible between the active and standby controllers. Any mismatch in IOS XE version will prevent SSO formation. License count (Option A) does not need to be identical for SSO. Service port IP addresses (Option E) must be unique per controller, not identical. Reference: WLSD Study Guide — Catalyst 9800 SSO Prerequisites, Redundancy Management Interface Configuration, High Availability Pair Formation Requirements.

Warehouse wireless deployments present unique RF engineering challenges: extremely high ceilings (often 25-45 feet), dense metallic shelving systems that create specular reflections and RF shadows, narrow aisles between rack systems, and the need to cover linear travel paths for RF scanner devices. The recommended Cisco antenna strategy for warehouses is wall-mounted patch (directional) antennas. Patch antennas provide a forward-facing radiation pattern that can be aimed precisely down warehouse aisles, delivering concentrated RF energy where RF scanners actually operate — in the aisles between shelving — rather than dispersing energy into metallic shelving structures. Wall mounting at intermediate height (typically 10-15 feet on aisle-end walls) places the antenna at a height that aligns the main lobe with the working zone of handheld scanners. Ceiling-mounted omnidirectional antennas (Options A and C) at warehouse ceiling height suffer from excessive path loss to floor-level devices and metal shelving obstructions. Low-gain wall-mounted omnidirectional antennas (Option B) lack the directivity needed to focus energy down specific aisles. Reference: WLSD Study Guide — Warehouse Wireless Design, Antenna Selection and Placement, Industrial RF Environment Considerations.

When designing a wireless network for any environment, including a historic building with ornate wall coverings and aesthetic constraints, RF coverage must always be considered first when placing access points. RF coverage is the fundamental requirement — without adequate signal strength throughout the space, no other design objective can be met. The engineer must first determine AP locations that provide the required signal strength and coverage to all areas before addressing aesthetics, overlap calculations, or interference mitigation. In a historic building specifically, the ornate wall coverings and dense construction materials may cause unexpected signal attenuation, making it even more important to model RF coverage before committing to AP positions. Once RF coverage requirements are established, aesthetic concerns (Option A) can guide the choice of AP form factor, enclosures, or cabling routes. Cell overlap (Option C) is derived from coverage calculations. RF interference (Option D) analysis follows after RF coverage baseline is established. Reference: WLSD Study Guide — Site Survey Methodology, AP Placement Priority, Special Environment Wireless Design.

In an N+1 redundancy deployment, an AP ' s ability to return to its designated primary WLC after that controller recovers depends on two distinct configuration requirements working in concert. First, the AP Fallback feature (Option C) must be enabled on the WLC. AP Fallback instructs APs to monitor the availability of their configured primary controller and automatically reconnect to it when it becomes available again, rather than remaining permanently joined to the N+1 backup controller. Without AP Fallback enabled, APs stay connected to whichever controller they most recently joined. Second, the APs must have their primary WLC information correctly configured (Option D). If an AP does not have the primary controller ' s name, IP address, or FQDN correctly set, it cannot identify when its designated primary has recovered and therefore cannot initiate a return fallback. DHCP Option 43 (Option A) is used for initial AP discovery only. Secondary WLC configuration (Option B) addresses failover direction but not the return path. AP failover priority (Option E) controls which APs are moved first during a failover event, not whether fallback occurs. Reference: WLSD Study Guide — N+1 Redundancy Design, AP Fallback Configuration, Controller Primary, Secondary and Tertiary Assignment.

In a wireless network design where anchor redundancy is required for guest access, setting different priorities for the anchor controllers ensures deterministic primary and backup behavior. Cisco anchor priority uses a lower numerical value to indicate higher preference — Priority 1 is the highest priority (most preferred) anchor, and Priority 3 is lower priority. Setting Anchor A to priority 1 (Option D) makes it the primary anchor controller — all new guest client sessions will preferentially anchor to Anchor A. Setting Anchor B to priority 3 makes it the standby anchor — guest clients will only be anchored to Anchor B when Anchor A is unavailable. This creates a clear primary/backup relationship with deterministic failover. Setting both anchors to the same priority (Options A and C) would result in load balancing between the two anchors rather than active/standby behavior. Option B incorrectly reverses the priorities, making Anchor B the primary and Anchor A the backup. Reference: WLSD Study Guide — Guest Anchor Redundancy Design, Anchor Priority Configuration, DMZ Anchor WLC Architecture.

In a mixed deployment where a Cisco Catalyst 9800 IOS XE WLC operating in SSO is required to establish a mobility peer relationship with a legacy AireOS WLC, the critical configuration requirement is that the 9800 SSO pair presents a single, consistent mobility MAC address to all peer WLCs. When the 9800 is in SSO mode, the active and standby controllers function as a single logical entity, but AireOS WLCs identify mobility peers by MAC address. If the MAC address changes during an SSO switchover, the AireOS peer will detect the change and tear down the mobility tunnel, disrupting inter-controller client roaming. The command ' wireless mobility mac-address < MAC > ' configures a static, persistent mobility MAC address on the 9800 SSO pair that remains constant regardless of which physical unit is active. This ensures the AireOS WLC always identifies the 9800 pair by the same MAC address, maintaining the mobility tunnel and enabling seamless client roaming. Option A configures the HA interface for SSO synchronization but not for AireOS mobility interoperability. Option B sets a default gateway. Option D enables management gateway failover, unrelated to mobility peer identification. Reference: WLSD Study Guide — IOS XE WLC SSO Configuration, AireOS to 9800 Migration, Mobility Peer MAC Address Management.

An oil terminal presents specific wireless design constraints: the requirement is pervasive coverage (maximum geographic coverage) for low-bandwidth applications (casual web and email). These requirements prioritize coverage reach over throughput optimization. The correct approach is to keep all data rates enabled, including lower rates such as 6, 9, 12, and 18 Mbps — because in an industrial environment with challenging RF propagation paths, reflective surfaces, and potential obstructions, lower data rates extend the functional coverage range of each AP. Web and email traffic does not require high data rates; even 1-6 Mbps is sufficient for these applications. Disabling rates below 54 Mbps (Option A) would dramatically shrink each AP ' s effective coverage area, requiring many more APs for pervasive coverage and failing the primary design objective. Assigning static maximum power without RRM auto-adjustment creates excessive co-channel interference. Disabling rates below 24 Mbps (Option C) still reduces coverage reach unnecessarily. Disabling 802.11n and 802.11ac MCS rates (Option D) prevents the AP from using high-efficiency modulation for nearby clients without coverage benefit. Auto power assignment combined with all rates enabled provides the optimal balance for pervasive industrial deployment. Reference: WLSD Study Guide — Industrial WLAN Design, Coverage vs. Capacity Trade-offs, Data Rate Configuration for Pervasive Coverage.