400-007 Exam Dumps - Cisco CCDE v3.0 Questions and Answers

When data center fabrics are extended across multiple private and public clouds, as in hybrid or multi-cloud designs, enterprises benefit from:

C. Ability to place workloads across clouds: Application and workload mobility is a key outcome of interconnected data center fabrics. It supports disaster recovery, scaling, and cost optimization strategies.

D. Centralized visibility: Modern SDN/cloud-integrated platforms offer centralized control and monitoring across domains, giving IT teams end-to-end insight regardless of workload location.

These principles support the CCDE v3.1 goals for cloud-aligned architecture, which promotes flexibility, operational simplicity, and global-scale services.

Why other options are incorrect:

A: Enhanced security is a benefit but not guaranteed simply by interconnecting clouds; it depends on the actual security controls in place.

B: Cloud deployments may compromise data and network ownership, especially in public models.

E: Cloud mobility is typically bidirectional when fully designed; unidirectional behavior is limiting and not an intended design goal.

In OSPF, a ring topology typically converges more slowly because:

Link failures can create longer SPF recalculations as alternate paths are fewer.

Only one alternate path usually exists for each link failure, extending the time needed for failure detection and SPF recalculation.

CCDE v3.1 stresses that designs like full mesh or triangulated topologies provide faster convergence due to multiple available alternate paths, which reduce SPF computation complexity.

Why other options are incorrect:

A, D, E: These topologies provide multiple paths.

B: Full mesh offers immediate redundancy for any failure.

—

B: Faster control plane convergence reduces the total recovery time after failure detection.

D: Enabling lower layer detection (such as BFD or physical layer link failure detection) shortens the time it takes to notify the control plane about link failure.

Why other options are incorrect:

A: Stability improves network operation but doesn’t address detection delay directly.

C: Interface flaps notification frequency doesn’t reduce initial detection delay — could actually create instability.

—

iBGP’s full mesh requirement refers to logical BGP session establishment, not physical network design. As long as reachability exists between iBGP peers (through an IGP like OSPF or IS-IS), iBGP sessions can be established regardless of physical topology (ring, star, partial mesh, etc.).

Key CCDE v3.1 design principles:

Logical iBGP mesh ≠ physical mesh requirement.

Physical topologies can be optimized independently of iBGP peering structure.

Control plane designs like route reflectors or confederations further optimize scalability without changing physical topology.

Why other options are incorrect:

B: iBGP works on any topology where IP reachability exists.

C: Physical full mesh is unnecessary for iBGP.

D: iBGP functions over any IGP-provided reachability domain, including rings.

D (Group Encrypted Transport VPN - GET VPN):GET VPN encrypts traffic across private WANs like MPLS while maintaining full-mesh routing visibility and offering centralized key management with minimal encapsulation overhead.

Other options explained:

A: S-VTI is used for point-to-point IPsec tunnels.

B: DMVPN is used for dynamic multipoint Internet-based VPNs.

C: MGRE is a tunneling protocol but lacks security features.

A (IaaS within a private cloud):IaaS allows on-demand scaling of compute and storage resources, and private cloud deployment reduces capital expenditures by pooling hardware resources and increasing utilization, while allowing control over security and compliance.

Other options explained:

B: On-prem IaaS still requires significant CapEx.

C: PaaS delivers platform services, but the scenario is focused on network systems.

D: SaaS on-prem is uncommon and does not address infrastructure scaling.

When unmanaged switches are connected to access ports, there ' s a risk that they may start participating in Spanning Tree Protocol (STP) or introduce loops. BPDU Guard is the most effective mechanism to mitigate this risk:

BPDU Guard disables a port immediately upon receiving any BPDU, ensuring that only end hosts (non-switch devices) are connected to access ports.

This protects the stability of the STP topology by preventing accidental or malicious introduction of switches into the Layer 2 domain.

Other options explained:

A (PortFast): Accelerates port transition to forwarding state but does not protect against loops caused by BPDUs.

B (UDLD): Detects unidirectional physical link failures but not STP participation.

C (Root guard): Prevents the connected device from becoming a root bridge but still allows BPDUs.

—

In an IS-IS design, placing the Level-1/Level-2 (L1/L2) boundary at the core limits the extent of the flooding domain, improving scalability and stability.

By limiting Level-2 flooding to the core, instability or frequent changes in the access/distribution layers (typically Level-1) do not impact the core.

The core remains stable, while routing changes are isolated within the Level-1 domains.

Other options explained:

A: Overlapping domains are not a design objective.

B: This has no direct impact on Layer 1 complexity.

C: IS-IS design must match topology hierarchy; this is not universally applicable.

—