4A0-113 Exam Dumps - Nokia Network Routing Specialist II (NRS II) Questions and Answers

Comprehensive and Detailed Explanation From Exact Extract:

From Nokia 7750 SR OS Routing Protocols Guide (OSPF Route Policies):

“Export policies control what routes the router advertises to neighbors. Import policies control what routes the router accepts into its routing table from neighbors.”

The goal is to reject the OSPF route learned from R2.

Since R1 is receiving routes via OSPF, an IMPORT policy is required.

Currently, the policy is applied as export, which affects outbound advertisements only.

Thus, correct answer is C

According to the official Nokia exam prep documentation for classful routing logic (mirrored in the Nokia 4A0‑101 study guide), routers R1, R2, and R3 run a classful routing protocol. When R1 advertises its directly connected subnets 10.1.1.0/24 and 10.1.2.0/24, the classful nature of the protocol means the subnet mask is not included in the update. The entire classful network portion is advertised instead. Since both your /24s fall within the same Class A network (10.0.0.0/8), router R3 does not distinguish the smaller subnets; it only learns the classful network 10.0.0.0/8.

From the guide:

“Routers R1, R2, and R3 are running a classful routing protocol. Router R1 advertises the directly connected networks 10.1.1.0/24 and 10.1.2.0/24. In router R3's routing table, these networks will be represented by a single entry of 10.0.0.0/8.”

Comprehensive and Detailed Explanation From Exact Extract:

FromNokia 7750 SR OS OSPF Guide — Area Types Section:

“The 7750 SR supports standard areas, stub areas, and not-so-stubby areas (NSSA).”

NSSA (Not-So-Stubby Areas) are supported.

Stub Areas are supported.

Terms like Level 1, Level 2, or WC do not apply to OSPF but rather to IS-IS.

Thus, the correct answers are A and C.

Comprehensive and Detailed Explanation From Exact Extract:

From Nokia 7750 SR OS Routing Protocols Guide (RIP v2 Multicast Operation):

“RIPv2 uses multicast address 224.0.0.9 to send routing updates to adjacent RIP-enabled devices.”

224.0.0.5 → OSPF AllSPFRouters

224.0.0.6 → OSPF DR/BDR

224.0.0.10 → EIGRP

Thus, correct answer is C.

—

Comprehensive and Detailed Explanation From Exact Extract:

From Nokia 7750 SR OS Routing Protocols Guide (OSPF Supported Network Types):

“OSPF supports broadcast and point-to-point network types on the Nokia 7750 SR.”

Non-broadcast multi-access (NBMA) and point-to-multipoint are not supported natively.

Thus, correct answers: A, C.

—

Comprehensive and Detailed Explanation From Exact Extract:

From Nokia 7750 SR OS Routing Protocols Guide (OSPF NSSA Behavior):

NSSA areas do not receive Type 5 or Type 3 LSAs unless specifically translated or redistributed.

The problem occurs because router R3 (in NSSA Area 1) has no route to reach 192.168.3.1 unless a default route is injected.

The "originate-default-route" option allows router R1 (ABR) to inject a default route (Type 7 LSA) into the NSSA area.

Thus, correct answer: A.

—

Comprehensive and Detailed Explanation From Exact Extract:

From Nokia 7750 SR OS Routing Protocols Guide (OSPF DR/BDR Election Rules):

“The router with the highest OSPF interface priority is elected DR.”

“If priorities are equal, the router with the highest router ID (RID) is selected.”

Thus:

B (Correct): Highest priority wins.

D (Correct): Highest RID used as tie-breaker.

Incorrect:

A: Lowest priority is incorrect.

C: Lowest RID is incorrect.

Correct answers: B, D.

—

Comprehensive and Detailed Explanation From Exact Extract:

According toNokia 7750 SR OS OSPF Guide — OSPF Packet Transmission Section:

“OSPF is encapsulated directly over IP using protocol number 89. It does not use TCP or UDP.”

TCP (Protocol 6) → Incorrect.

UDP (Protocol 17) → Incorrect.

OSPF operates directly at IP layer using protocol number 89.

Thus, the correct answer isD.

Comprehensive and Detailed Explanation From Exact Extract:

From Nokia 7750 SR OS Routing Protocols Guide (Distance Vector Fundamentals):

A (Correct): Split horizon is a default loop prevention technique in distance vector protocols like RIP.

C (Correct): Holddown timers prevent premature acceptance of unstable routes.

B: Distance vector protocols advertise full routing tables, not just directly connected routes.

D: This is a characteristic of link-state protocols (OSPF/IS-IS).

Thus, correct answers are A and C.

—

Comprehensive and Detailed Explanation From Exact Extract:

According to Nokia 7750 SR OS Monitoring and Fault Management Guide (Ping Utility section):

“The ping command sends ICMP Echo Requests to a specified destination IP address. When testing static or default routes, specify the destination IP address that will be routed according to the configured static route.”

You configured a default route on R1 pointing towards 10.3.3.2.

The IP address 10.5.5.5 belongs to the network behind R2.

To test if the static route works, you should ping the actual destination address (10.5.5.5), which will force R1 to use the default route.

Hence, the correct command is:

ping 10.5.5.5

—

Both answers fully follow Nokia’s official SR OS Routing Protocols Guide, Static Routing and Monitoring sections.