H35-211_V2.5 Exam Dumps - Huawei HCIP-Access Questions and Answers

Huawei GPON design recommends at most two splitting stages and a total split ratio within the optical power budget (commonly up to 1:64 for standard budgets).

A: 1:2 × 1:16 = 1:32 (valid).

C: 1:8 × 1:8 = 1:64 (valid under standard budgets).

D: 1:2 × 1:8 = 1:16 (valid).

B: 1:16 × 1:16 = 1:256, which exceeds typical GPON budgets and recommended engineering practice. Hence B is the incorrect networking.

For OLT uplink (NNI) protection groups (timedelay/weight, etc.), Huawei requires that each physical port belongs to one protection group only to avoid conflicting switchover control. A member port cannot be part of multiple protection groups simultaneously.

Huawei QoS describes PQ (Priority Queuing) as the strict-priority scheduler ensuring that high-priority queues are served first before lower-priority queues. WRR/DRR/RR are weighted or round-robin modes intended for fair sharing and do not guarantee strict preemption for latency-sensitive traffic. Therefore, PQ is selected for higher-priority services (e.g., voice, control).

Standard OTDR operation allows you to configure multiple acquisition parameters:

Measurement range (distance range): sets the maximum span to be traced; best practice is typically 1.5–2× the fiber length under test.

Wavelength: select test wavelength(s), e.g., 1310/1550 nm for SM fiber, to observe different loss characteristics.

Mode: vendors provide real-time/average (or similar) acquisition modes to stabilize traces.

Pulse width: controls dynamic range vs. event resolution; longer pulses see farther but increase dead zones, while shorter pulses improve resolution at the cost of range.

These are documented in foundational OTDR references and application notes.

In GPON, DBA (Dynamic Bandwidth Allocation) operates in the upstream direction. The OLT grants upstream transmission opportunities to ONTs by assigning T-CONT bandwidth (Fixed/Assured/Non-Assured/Best-Effort) within upstream frames. The downstream direction is a continuous broadcast stream from the OLT at the fixed GPON line rate; user traffic is multiplexed without DBA. Hence, DBA is upstream-only; downstream traffic is not DBA-scheduled.

Huawei GPON service provisioning supports mapping upstream/downstream service flows to GEM Ports using multiple classifiers, including MAC address, physical port (PORT), VLAN ID, and 802.1p (priority). These classifiers are configured in line/service templates (and pushed via U2000) to ensure precise flow-to-GEM binding.

In SIP, each proxy/server that forwards a request prepends its own address to the top of the Via header list. Therefore, as A’s INVITE traverses C, then D, then E, server E adds its Via at the top last, followed by D, then C below it. The message that reaches user B shows the Via stack (top→bottom) as E → D → C, which corresponds to option C. RFC 3261 states that the server transport uses “the value of the top Via header field” to determine response routing, confirming that the most recent hop is at the top

Per RFC 3261 (SIP), “The CSeq header field of the response MUST equal the CSeq field of the request.” CSeq carries a sequence number and the method, thereby associating a response with the specific request it answers. While Call-ID ties together all messages within the same dialog, it does not identify the specific request/response pairing; CSeq does. Therefore, CSeq is the correct header for correlating a response to the exact request.

The OLT’s anti–IP-attack (control-plane protection) function identifies and rate-limits abnormal or attack traffic to protect the CPU. It does not block legitimate management protocols such as Telnet/SSH by design. Remote management remains available when sourced from permitted hosts and within configured thresholds; administrators can also use trusted-host/ACL policies if needed.

On Huawei access devices/OLTs, VoIP/H.248 setup typically includes:

In voip view, configure media IP with gateway:

ip address media – e.g., ip address media 10.10.10.10 10.10.10.1.

Configure signaling IP without a gateway parameter:

ip address signaling – e.g., ip address signaling 10.10.10.10.

Add/enter the H.248 interface and apply properties with if-h248 attribute ….

It’s common to reset/enable the MG interface after attribute changes; many guides show reset coldstart (or reset) issued under the H.248 interface to activate the interface.

Authoritative configuration examples show media takes an IP and gateway, but signaling takes only the IP. Therefore, option D (attempting to configure signaling with a gateway parameter) is incorrect. Options A and C match documented syntax and workflow. Option B reflects the documented practice of issuing a reset (often written as reset coldstart) under the H.248 interface to apply/enable, as shown in Huawei-focused configuration guides.