H12-821_V1.0 Exam Dumps - Huawei HCIP-Datacom Questions and Answers

Comprehensive and Detailed In-Depth Explanation:

IPsec (IP Security Protocol) establishes Security Associations (SAs) for encrypted communication.

An SA is uniquely identified by a 3-tuple:

SPI (Security Parameter Index) → Identifies the SA.

Destination IP Address → Specifies the receiving device.

Security Protocol ID → Indicates whether AH (Authentication Header) or ESP (Encapsulating Security Payload) is used.

A. Key exchange protocol is not part of the SA 3-tuple. It is used during IKE (Internet Key Exchange) but is not part of the SA itself.

???? Reference: Huawei HCIA-Datacom Study Guide, IPsec Security Association and SA Identification.

In IS-IS:

Level-1 routers can only form neighbor relationships with other Level-1 routers in the same area.

Level-2 routers can form neighbor relationships with other Level-2 routers regardless of area ID.

Level-1-2 routers can form relationships at both levels depending on the peer's configuration.

So, if two Level-1 routers have different area addresses, they cannot establish a neighbor relationship.

Reference from Huawei HCIP-Datacom-Core Technology Study Guide:

“Level-1 routers must have the same area address to establish neighbor relationships. Level-2 routers can peer across different areas.”

(Chapter: IS-IS Protocol Principles – Section: Neighbor Establishment)

The Forwarding Information Base (FIB) is derived from the router's routing table and contains the exact forwarding entries used to route packets. It directly guides packet forwarding decisions by matching incoming packets with the correct output interface or next-hop address ​.

Comprehensive and Detailed Step-by-Step Explanation:

1. Understanding LSA Filtering in OSPF and IS-IS:

The filter-policy command is used in OSPF and IS-IS to control which routing information is imported into the local routing table or advertised to other neighbors.

However, it cannot filter LSAs forwarded by neighbors. In OSPF and IS-IS, LSAs are always forwarded unchanged within the area to ensure all routers have a consistent link-state database.

Filtering only affects the routes that are installed into the local routing table or advertised to other areas or neighbors.

2. Why the Statement is False:

LSAs are forwarded without being filtered. This ensures link-state protocols maintain the same network topology view across the network.

The filter-policy import command only controls routes that are installed into the local routing table, not the forwarding of LSAs.

3. Summary:

The statement is FALSE because LSAs cannot be filtered by filter-policy import.

Huawei HCIA-Datacom Study Guide, Chapter "OSPF Route Filtering."

RFC 2328: OSPF Version 2, LSA Propagation Rules.

Comprehensive and Detailed In-Depth Explanation:

A. TRUE → The interface GigabitEthernet0/0/1 has an IP address of 192.168.1.1.

B. TRUE → The IGMP version is explicitly stated as IGMPv2.

C. TRUE → The maximum query response time for IGMP is set to 10 seconds.

D. TRUE → The IGMP Query Interval is configured as 60 seconds, meaning the router sends Group-Specific Queries every 60 seconds.

???? Reference: Huawei HCIA-Datacom Study Guide, IGMP Configuration and Query Timers.

IPv4 supports three main transmission modes:

Unicast: One-to-one communication.

Broadcast: One-to-all communication within a network.

Multicast: One-to-many communication to a group of interested receivers.Anycast is not a native IPv4 mode but is introduced in IPv6 ​.

Inter-area route calculation in OSPF involves Summary LSAs (Type 3) for summarizing routes across areas and ASBR Summary LSAs (Type 4) for locating ASBRs. While Router LSAs and Network LSAs describe the internal structure of an area, they do not directly participate in inter-area route calculation. Thus, the statement that only Router, Network, and Summary LSAs are involved is false ​.

The error indicates "Incorrect remote AS," which refers to a mismatch in the autonomous system (AS) numbers during BGP peer configuration. This issue is unrelated to the neighbor address. The neighbor address (10.1.1.5) and timestamp (2010-03-22 12:40:39) provided in the output are correct, and the error type confirms a neighbor relationship issue ​.

The asbr-summary command is executed in the global OSPF view to summarize external routes. The abr-summary command is executed in the OSPF area view to summarize routes between areas. By default, the advertise parameter is enabled unless explicitly overridden by the not-advertise option ​.