220-1101 Exam Dumps - CompTIA A+ Questions and Answers

Installing an M.2 SSD will improve a workstation's overall response time for frequently used applications and data without removing the current hard drive. M.2 drives are faster and more efficient than traditional hard drives, making them a good option for increasing overall performance. References: CompTIA A+ Certification Exam Core 1 Exam Objectives - 1.5 Given a scenario, configure storage devices and use appropriate media

The flashing green and orange LEDs on the NIC indicate connection issues. The technician should first check for loose connections, pinched bends, and physical damage, which are the most common causes of connection problems. References: CompTIA A+ Certification Exam Guide, Ninth Edition, Chapter 14

The symptoms—flashing green and orange LEDs on the workstation’s NIC—suggest a connectivity issue. In networking troubleshooting, flashing LEDs typically indicate activity (green for link/activity, orange for speed or errors, depending on the NIC), but the combination and context imply an unstable or degraded connection. The cable length of 275ft (84m) is within the maximum distance for Cat 5 UTP (100 meters or 328 feet), so length alone isn’t the immediate problem. However, physical issues like loose connections, pinched bends, or damage could degrade signal quality, causing intermittent or erroneous data transmission.

The CompTIA A+ Core 1 Study Guide emphasizes a systematic troubleshooting approach, starting with the simplest and most common causes before escalating to more complex solutions. Checking the cable’s physical integrity—ensuring proper termination, no sharp bends, and no cuts or interference—is a fundamental first step in network troubleshooting. This aligns with Objective 5.5 ("Given a scenario, troubleshoot problems related to motherboards, RAM, CPU, and power") and Objective 5.2 ("Given a scenario, troubleshoot and diagnose problems with storage drives and RAID arrays"), which extend to networking in practice.

Option A (Check for loose connections, pinched bends, and physical damage): This is the least invasive, most immediate step to rule out common cabling issues, as recommended by CompTIA’s methodology.

Option B (Install a powered hub halfway): Adding a hub or repeater could extend signal strength, but the length is within spec, and this assumes a distance issue without evidence. It’s not the first step.

Option C (Replace with Cat 5 STP): Shielded twisted pair reduces interference, but there’s no indication of EMI yet, and replacing the cable is premature without basic checks.

Option D (Upgrade to multimode fiber): Fiber eliminates distance and interference issues but is a costly, last-resort solution, not a first step.

The study guide prioritizes physical inspection and basic diagnostics before hardware replacements or upgrades, making Option A the correct initial action.

Exact Extracts from the Study Guide:

From The Official CompTIA A+ Core 1 Study Guide (220-1101):

Section 2.6, Networking Hardware:

"Twisted Pair Cabling: The maximum length of a twisted pair cable run (such as Cat 5, Cat 5e, or Cat 6) is 100 meters (328 feet). This includes both patch cables and the main run. Beyond this length, signal degradation (attenuation) becomes significant, and a repeater or switch is needed to boost the signal."

Implication: At 275ft (84m), the cable is within spec, so length isn’t the primary concern.

Section 5.4, Troubleshooting Wired and Wireless Network Problems:

"No connectivity or intermittent connectivity—Check the following: Ensure that all cables are securely connected at both ends (NIC and switch or wall jack). Inspect the cable for damage, such as cuts, crimps, or excessive bending, which can disrupt signal integrity… Verify that the cable length does not exceed the maximum specification for the cable type (e.g., 100 meters for twisted pair)."

"LED indicators—Most NICs and switches have LED indicators to show link status and activity. A solid green light typically indicates a good connection, while flashing may indicate activity. Amber or orange lights can indicate speed (e.g., 10/100 Mbps vs. 1 Gbps) or errors, depending on the device."

Section 5.4, Troubleshooting Methodology:

"Identify the problem… Gather information… Establish a theory of probable cause… Test the theory to determine cause (e.g., check physical connections before replacing components)."

These excerpts highlight that checking physical connections and cable condition is the first step when LEDs indicate potential issues, especially before assuming hardware failure or specification limits are exceeded.

Additional Reasoning:

LED Behavior: Flashing green and orange LEDs vary by NIC manufacturer, but per the study guide, green flashing often means activity, and orange flashing could signal errors or a speed mismatch. This suggests a link is established but unstable, pointing to cabling issues.

Cable Length: At 275ft, the run is well under 328ft, ruling out immediate need for a hub or fiber upgrade.

Common Issues: Loose RJ45 connectors, pinched cables (exceeding bend radius), or physical damage are frequent causes of intermittent connectivity, easily checked first.

Alternatives: Installing a hub (B) or replacing the cable (C, D) assumes a specific failure without evidence, violating CompTIA’s step-by-step approach.

Rapid elasticity is only suitable for a domain whose resource requirements suddenly up and down for a specific time interval. Referring to the question the online retailer wants to migrate to public cloud services during peak season, then wants it to be removed "automatically" when the peak is over.

The MOST efficient next step the technician should complete is to install an updated printer driver on the print server12. The issue of information being garbled and looking like code could be related to a compatibility issue with the new firmware and the existing printer driver1. The printer driver is responsible for converting the print job data into a format that the printer can understand and print2. 

The most likely reason that the technician is unable to select the channel with almost no RF pollution is that it is reserved for licensed band use. Some channels are reserved for specific purposes and require a license to use. These licensed bands are typically used for critical infrastructure, public safety, or military operations, and unlicensed devices are not allowed to use them. References: CompTIA A+ Certification Exam Objectives - 220-1001: 3.3 Compare and contrast common networking hardware devices.

http://www.221021.com/Hardware/input-output-devices/32310.html

1. Identify the problem.

Gather information from the user, identify user changes, and, if applicable, perform backups before making changes.

Inquire regarding environmental or infrastructure changes.

2. Establish a theory of probable cause (question the obvious).

If necessary, conduct external or internal research based on symptoms.

3. Test the theory to determine the cause.

Once the theory is confirmed, determine the next steps to resolve the problem.

If the theory is not confirmed, re-establish a new theory or escalate.

4. Establish a plan of action to resolve the problem and implement the solution.

Refer to the vendor's instructions for guidance.

5. Verify full system functionality and, if applicable, implement preventive measures.

6. Document the findings, actions, and outcomes.

Mobile Device Management (MDM) software often controls access to corporate resources based on location, network, or VPN status. If the MDM is not configured to allow access from outside the office or via home networks, the apps may be blocked. This is the most probable cause if apps work only on-premises.

Option A: GPS is used for location services, not access control.

Option C: WPA is a Wi-Fi security protocol, not related to access restrictions.

Option D: NFC enables close-range communication — irrelevant to app access.

CompTIA A+ Core 1 Exam Objective Reference:

Objective 1.6: Given a scenario, configure basic mobile device network connectivity and application support.

Switches only send data to the specific computer, while hubs send data to all computers inside the network. References: CompTIA A+ Certification Exam Guide, Exam 220-1001, Page 323

PaaS (Platform as a Service) is a cloud computing model in which a provider offers a platform that allows developers to create, run, and manage applications without the complexity of building and maintaining the infrastructure. An application development environment is a valid use for PaaS. References: CompTIA A+ Certification Exam Objectives 1001, 1.7

A scratch on the scanning bed of a copier can cause a solid black line to appear on all copies, as the scanner cannot read the original document properly through the scratch. The scratch can also reflect light and create noise in the scanned image. The printing function is unaffected by the scratch, as it does not use the scanning bed. The technician should inspect and clean the scanning bed, and replace it if necessary. Reference: https://partners.comptia.org/docs/default-source/resources/a-core-1-content-guide (page 16)

Automatic document feeder (ADF) is a feature that allows a multifunction printer to photocopy documents with hundreds of pages automatically without requiring manual intervention. ADF scans multiple pages from a stack of documents and feeds them into the printer one by one. SMB is a network protocol that allows file sharing and printer access among different devices on a network. PCL is a printer language that controls how data is formatted for printing. SSH is a network protocol that allows secure remote access to another device over an encrypted connection.

The message stating that one or more disks are in a degraded state is a clear indication of a RAID failure. RAID stands for Redundant Array of Independent Disks, and it is a technology used to provide fault tolerance and improve performance by combining multiple hard drives into a single logical unit.

The message indicating that the OS is missing is most likely caused by a bootable device not found. This means that the server is unable to boot from the designated boot device, which could be the hard drive, a CD/DVD drive, or a USB flash drive. This could be caused by a faulty boot device, a loose cable, or a misconfiguration in the BIOS or UEFI settings.

Client-side virtualization guest machines require isolation from other guest machines to maintain their security. Isolation ensures that each virtual machine is separated from others and runs its own operating system and applications, making it less vulnerable to attacks from other guest machines. References: CompTIA A+ Certification Exam Objectives 220-1002 - Virtualization and cloud computing - 4.1

Thin, vertical lines on every printed page are usually caused by a dirty drum or toner cartridge. Performing the drum-cleaning procedure will likely resolve the issue. References: CompTIA A+ Certification Exam Guide, Ninth Edition, Chapter 18

If a user is unable to connect a laptop to a projector or videoconferencing system and sees the error message "No source found," the next step should be to check the display settings on the computer and set them to extend/duplicate. This will ensure that the laptop's display is being output to the external device. References: CompTIA A+ Certification Exam Guide, pg. 514

Two-factor authentication (2FA) is a security process that requires users to provide two different authentication factors to verify their identity. This means that in addition to providing something they know (such as a password or PIN), they must also provide something they have (such as a smart card or token) or something they are (such as a fingerprint or retinal scan).

In this case, the correct answer would be C. Password/thumbprint. This option meets the requirement for two-factor authentication because it combines two different types of authentication factors: something the user knows (the password) and something the user is (the thumbprint). The other options do not meet the requirement for 2FA because they either use only one type of authentication factor (A and D) or use two instances of the same type of factor (B).

The 2. band is subdivided into up to 14 channels, spaced at 5 MHz intervals from 2412 MHz up to 2484 MHz. Wi-Fi requires bandwidth of approximately 20 MHz, not 5 MHz. Consequently, a site designer needs to choose the channels that do not overlap. On a WLAN where only the first 11 channels are available, channels 1, 6, and 11 can be selected as non-overlapping. Note: In the Americas, regulations permit the use of channels 1-11 only, while in Europe, channels 1-13 are permitted. In Japan, all 14 channels are permitted.

The issue described in the question is most likely due to an incorrect configuration of the printer's duplex settings. To enable automatic duplex printing, the technician needs to read the printer's installation manual to understand how to configure the printer's duplex settings correctly. Once the settings are configured, the printer should be able to print on both sides of the paper automatically.

To fix the issue of a newly installed printer capable of automatically printing on both sides of the paper but only printing on both sides manually, the technician should read the installation manual and configure duplex settings. Duplex printing settings can be configured in the printer driver software, which can be accessed through the printer settings in the Control Panel. Installing the most recent firmware upgrade available for the printer, contacting the vendor for a hardware replacement, or reinstalling the printer software and drivers and restarting the printer will not resolve the issue.

The clicking sound is the sound of a damaged disk in the HDD

A clicking sound from a hard disk drive typically indicates a mechanical failure, such as the read/write head hitting a physical obstruction or a problem with the disk motor. This can cause the drive to fail to initialize or not be recognized by the system during booting.

FTP (File Transfer Protocol) uses TCP ports 20/21 and transfers data in cleartext, which means the data is not encrypted and can be read by anyone who intercepts it. This makes FTP insecure for transferring sensitive information. SSH (Secure Shell), on the other hand, uses port 22 and encrypts data, making it more secure. SNMP (Simple Network Management Protocol) uses ports 161/162 and is used to monitor network devices. Telnet uses port 23 and transfers data in cleartext, making it insecure. References: CompTIA A+ Certification Exam: Core 1 - Page 199