CWNA-109 Exam Dumps - CWNP CWNA Questions and Answers

PoE has different standards that define different power levels for PSEs and PDs. The original standard, IEEE 802.3af, defines two classes of PSEs: Class 3 (15.4 W) and Class 4 (30 W). The newer standard, IEEE 802.3at, also known as PoE+, defines four classes of PSEs: Class 0 (15.4 W), Class 1 (4 W), Class 2 (7 W), and Class 3 (12.95 W). The power level received at the PD is always lower than the power level provided by the PSE, due to cable resistance and power dissipation. The IEEE standards specify the minimum power level that must be received at the PD for each class of PSE. For a Class 4 PSE, the minimum power level received at the PD is 25.5 W910. References: CWNA-109 Study Guide, Chapter 7: Power over Ethernet (PoE), page 295; CWNA-109 Study Guide, Chapter 7: Power over Ethernet (PoE), page 289.

A 5 GHz channel should be used for this AP because channels 1 and 6 are 2.4 GHz channels and they have no impact on the decision. The 5 GHz frequency band offers more non-overlapping channels than the 2.4 GHz frequency band, which reduces interference and improves performance. The 5 GHz frequency band also supports higher data rates and wider channel bandwidths than the 2.4 GHz frequency band, which increases capacity and throughput. The 5 GHz frequency band also has less interference from other devices and sources than the 2.4 GHz frequency band, which enhances reliability and quality of service. Therefore, it is recommended to use the 5 GHz frequency band for WLANs whenever possible. Channels 1 and 6 are two of the three non-overlapping channels in the 2.4 GHz frequency band (the other one is channel 11). They are used by a neighbor network in this scenario, but they do not affect the channel selection for this AP because they operate in a different frequency band than the 5 GHz frequency band. Channel 6 is not always best to use; it depends on the interference and congestion level in the environment. Channel 1 is not best to use because it has a lower frequency than channel 6; frequency does not determine channel quality or performance. Channel 11 is not best to use because it is also a 2.4 GHz channel and it may interfere with channels 1 and 6. References: CWNA-109 Study Guide, Chapter 4: Antenna Systems and Radio Frequency (RF) Components, page 113

The center frequency of channel 4 in the 2.4 GHz band is 2.427 GHz (2427 MHz). The center frequency of a channel is the midpoint of its frequency range, where the signal strength is highest and most concentrated. The center frequency of channel 1 in the 2.4 GHz band is 2.412 GHz (2412 MHz), as given in the question. The center frequency of each subsequent channel is obtained by adding 5 MHz to the previous channel’s center frequency, since the channels are spaced 5 MHz apart from each other in this band. Therefore, to find the center frequency of channel 4, we need to add 15 MHz (5 MHz x 3) to the center frequency of channel 1:

2.412 GHz + 0.015 GHz = 2.427 GHz

Alternatively, we can use a formula to calculate the center frequency of any channel in the 2.4 GHz band:

Center frequency (GHz) = 2.407 + (0.005 x Channel number)

Using this formula for channel 4, we get:

Center frequency (GHz) = 2.407 + (0.005 x 4)

Center frequency (GHz) = 2.407 + 0.02

Center frequency (GHz) = 2.427 References: 1, Chapter 3, page 85; 2, Section 3.2

The two IEEE amendments that should be supported to provide the management frame protection and fast secure roaming security features are 802.11r and 802.11w12.

802.11r (Fast BSS Transition): This amendment to the IEEE 802.11 standard permits continuous connectivity aboard wireless devices in motion, with fast and secure client transitions from one Basic Service Set to another1.

802.11w (Management Frame Protection): This amendment increases the security of its management frames2.

The CWNA Official Study Guide (CWNA-109), Chapter 8: Troubleshooting and Spectrum Analysis, explains that hidden node problems occur when two or more client stations cannot hear each other but can both communicate with the same access point. This leads to collisions at the AP because the clients transmit simultaneously without sensing each other’s signals.

“Hidden node problems can often be identified in a protocol analyzer by observing excessive retransmissions from specific client stations. These retransmissions occur because the station’s frames are not acknowledged due to collisions caused by other stations that the transmitter cannot hear.”

— CWNA-108 Study Guide, Chapter 8, Hidden Node Problem Analysis, p. 393–395

Therefore, when analyzing for a hidden node issue, you will typically observe:

Retransmitted frames from multiple STAs.

Higher retry counts for affected stations compared to others.

Hence, the correct answer is C. Retransmitted frames from multiple STAs with higher retry counts than other STAs.

The client STA can use Beacon frames transmitted by the AP to verify that an AP supports the same data rates that it supports. Beacon frames are management frames that are periodically broadcasted by the APs to announce their presence, capabilities, and parameters. One of the information elements contained in the Beacon frames is the Supported Rates or Extended Supported Rates, which lists the data rates that the AP can use for communication. The client STA can compare its own data rates with those advertised by the AP to determine if they are compatible. Data frames, authentication frames, and probe request frames do not contain information about data rates. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 133; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 123.

Authenticated and Unassociated. According to one of the web search results1, a STA can be authenticated to multiple APs, but it can only be associated to one AP at a time. Association is the process of establishing a logical link between the STA and the AP, which allows the STA to send and receive data frames through the AP2. Therefore, when a STA has authenticated to an AP-1, but still maintains a connection with another AP-2, it means that the STA is authenticated to both APs, but only associated to AP-2. The state of the STA on AP-1 is authenticated and unassociated, which means that the STA can switch to AP-1 without repeating the authentication process, but it cannot send or receive data frames through AP-1 until it becomes associated.

In the 2.4 GHz frequency band used for 802.11 wireless networks, the channel bandwidth is typically 20 MHz, but the actual frequency spread of each channel is about 22 MHz due to the modulation techniques used. This spread causes overlap between adjacent channels, which can lead to interference and degrade network performance. To avoid this, it's essential to use non-overlapping channels.

The three non-overlapping channels in the 2.4 GHz band are 1, 6, and 11. Each of these channels is spaced sufficiently apart to avoid interference with each other:

Channel 1: Centered at 2.412 GHz.

Channel 6: Centered at 2.437 GHz.

Channel 11: Centered at 2.462 GHz.

Given the options provided, option C (1 and 5) is the closest to a pair of non-overlapping channels, although in practice, channel 5 would still cause some interference with channel 1 due to the 22 MHz spread. The ideal choice for non-overlapping channels would be any two channels among 1, 6, and 11, but this is not an option provided. Therefore, within the given options, 1 and 5 are the best choice, understanding that in a real-world scenario, 1 and 6 or 6 and 11 would be preferred to avoid overlap.

The beamwidth of an RF antenna is the angular measure of how wide the main lobe of radiation is. The main lobe is the area where the signal strength is highest and most concentrated. The beamwidth is calculated at the points where the main lobe decreases power by 3 dB, which means it is half of the maximum power. The beamwidth can be measured in both horizontal and vertical planes, depending on how the antenna is oriented. The horizontal beamwidth is also called azimuth, while the vertical beamwidth is also called elevation. The beamwidth patterns on an antenna polar chart indicate how the RF energy is distributed in different directions. References: 1, Chapter 2, page 66; 2, Section 2.3