CWNA-109 Exam Dumps - CWNP CWNA Questions and Answers

 VSWR stands for Voltage Standing Wave Ratio, which is a measure of how well the impedance of the RF cable and connectors matches the impedance of the transmitter and the antenna. Impedance is the opposition to the flow of alternating current in an RF circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. A perfect impedance match would have a VSWR of 1:1, meaning that all the power is transferred from the transmitter to the antenna, and none is reflected back. However, in reality, there is always some degree of mismatch, which causes some power to be reflected back to the transmitter, creating standing waves along the cable. This reduces the efficiency and performance of the wireless system, and can also damage the transmitter. Excessive VSWR can be caused by using poor quality or damaged cables and connectors, or by using components that have different impedance ratings123. References: CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 90; CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 86; CWNP website, CWNA Certification.

An ACK (Acknowledgement) frame is a short control frame that is sent by the receiver of a data or management frame to confirm that the frame was received correctly. The ACK frame is sent after a SIFS (Short Interframe Space) interval, which is the shortest time gap between frames in 802.11. If the transmitter does not receive an ACK frame within a specified time, it assumes that the frame was not delivered and must be retransmitted. This is part of the 802.11 reliability mechanism that ensures reliable data delivery over an unreliable wireless medium . References: [CWNA-109 Study Guide], Chapter 5: IEEE 802.11 Medium Access, page 209; [CWNA-109 Study Guide], Chapter 5: IEEE 802.11 Medium Access, page 203.

Discovering the scale of the problem is the next logical step in the troubleshooting process after identifying the problem of poor wireless connections on the third floor of a building under your administration. Troubleshooting is a systematic process of finding and resolving problems or issues in a network or a system. Troubleshooting usually follows a general methodology that consists of several steps or phases, such as:

Identifying the problem: This step involves defining and describing the problem clearly and accurately based on the symptoms and evidence observed or reported by users or administrators. For example, in this case, the problem is that three individuals have reported poor wireless connections on the third floor of a building.

Discovering the scale of the problem: This step involves determining how widespread and severe the problem is by gathering more information and data from different sources and perspectives. For example, in this case, this step could involve checking if other users or devices on the third floor or other floors are experiencing similar issues, verifying if there are any changes or updates in the network configuration or environment that could affect the wireless connections, testing if there are any differences in performance or quality between different access points or channels on the third floor, etc.

Performing corrective actions: This step involves applying possible solutions or fixes to resolve or mitigate the problem based on logical reasoning and analysis. For example, in this case, this step could involve adjusting the output power or channel assignment of the access points on the third floor, relocating or reorienting some access points or antennas to improve coverage or reduce interference, updating or replacing some faulty or outdated hardware or software components, etc.

Verifying the solution: This step involves confirming that the problem is solved or improved by testing and monitoring the network performance and user satisfaction after applying corrective actions. For example, in this case, this step could involve measuring and comparing the signal strength and throughput of wireless connections on the third floor before and after performing corrective actions, asking for feedback from users who reported poor wireless connections to see if their issues are resolved or reduced, etc.

Creating a plan of action or escalating the problem: This step involves documenting and reporting the problem and its solution for future reference and improvement purposes. It also involves deciding whether to close or escalate the problem depending on its status and severity. For example, in this case, this step could involve creating a report that summarizes what was done to troubleshoot and fix poor wireless connections on the third floor with relevant data and evidence to support it. It could also involve escalating poor wireless connections to higher-level administrators if they persist or worsen despite performing corrective actions.

To calculate the EIRP at the antenna element, we need to add the transmitter output power, subtract the cable loss, and add the antenna gain. All these values need to be converted to dBm first, if they are not already given in that unit. In this case, we have:

Transmitter output power = 50 mW = 10 log (50) dBm = 16.99 dBm Cable loss = 3 dB Antenna gain = 9 dBi

EIRP = Transmitter output power - Cable loss + Antenna gain EIRP = 16.99 - 3 + 9 EIRP = 22.99 dBm

Rounding up to the nearest integer, we get 23 dBm as the EIRP at the antenna element12. References: CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 92; CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 88.

The likely cause of the problem is that the external hard drive is USB 3.0 and is causing a significant increase in the noise floor when in use. USB 3.0 devices are known to generate radio frequency interference (RFI) in the 2.4 GHz band due to their high data transfer rates and harmonics. This RFI can increase the noise floor and degrade the signal-to-noise ratio (SNR) of WLAN devices operating in the same band. This can result in lower data rates, reduced throughput, increased retransmissions, and poor performance. The problem may not occur outside of business hours or on the user’s home network because of different usage patterns or environmental factors. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 527; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 497.

The scenario described suggests that while the Access Point (AP) is capable of 802.11ax (Wi-Fi 6) with four spatial streams, the clients are only achieving data rates typical of 802.11n (Wi-Fi 4) devices, which indicates that the clients are likely 802.11n devices. Here's why this is the most plausible explanation:

802.11n Limitations: Devices that adhere to the 802.11n standard have lower maximum data rates compared to 802.11ax devices due to differences in technology such as modulation, spatial streams, and channel bandwidth. An 802.11n device with a single spatial stream operating on a 20 MHz channel can achieve a maximum data rate of 72.2 Mbps. Even with two spatial streams under ideal conditions, this would only double to approximately 144.4 Mbps, which is close to the 150 Mbps mentioned.

Spatial Stream Capability: The fact that the AP supports four spatial streams suggests it can achieve much higher data rates with 802.11ax clients that also support multiple spatial streams. However, if the clients are 802.11n devices, they may not be capable of using more than two spatial streams, and many earlier 802.11n devices were limited to just one.

The other options are less likely to be the primary cause based on the information provided:

B. Two Stream 802.11ax Clients: If the clients were 802.11ax with only two spatial streams, they would likely achieve higher data rates than 150 Mbps due to the efficiency improvements in 802.11ax.

C. Contention and D. Non-Wi-Fi Interference: While these could affect performance, they would not inherently limit clients to 150 Mbps, especially in the context of an 802.11ax environment where mechanisms to handle interference and contention are more advanced.

OFDM (Orthogonal Frequency Division Multiplexing) is the physical layer specification (PHY) that VHT capable devices must be backward compatible with according to the IEEE 802.11-2012 standard. VHT (Very High Throughput) is a PHY and MAC enhancement that is defined in the IEEE 802.11ac amendment and is also known as Wi-Fi 5. VHT operates only in the 5 GHz band and uses features such as wider channel bandwidths (up to 160 MHz), higher modulation schemes (up to 256-QAM), more spatial streams (up to eight), multi-user MIMO (MU-MIMO), beamforming, and VHT PHY and MAC enhancements. VHT can achieve data rates up to 6.9 Gbps.

According to the IEEE 802.11-2012 standard, VHT capable devices must be backward compatible with devices using OFDM PHY, which is defined in the IEEE 802.11a amendment and is also used by IEEE 802.11g, IEEE 802.11n, and IEEE 802.11h amendments. OFDM operates in both the 2.4 GHz and 5 GHz bands and uses features such as subcarriers, symbols, guard intervals, and OFDM PHY and MAC enhancements. OFDM can achieve data rates up to 54 Mbps.

Backward compatibility means that VHT capable devices can interoperate with OFDM devices on the same network by using common features and parameters that are supported by both PHYs. For example, VHT capable devices can use a channel bandwidth of 20 MHz, a modulation scheme of BPSK, QPSK, or 16-QAM, one spatial stream, no beamforming, and OFDM PHY and MAC headers when communicating with OFDM devices. Backward compatibility also means that VHT capable devices can fall back to OFDM mode when the signal quality or SNR is too low for VHT mode. References: 1, Chapter 3, page 123; 2, Section 3.2

The common spectrum analyzer view that you should use for this analysis is the Waterfall/Spectrogram view. The Waterfall/Spectrogram view shows the signal from the interfering device over time on a three-dimensional graph. The x-axis represents frequency, the y-axis represents time, and the z-axis represents amplitude or power. The color of each pixel indicates the signal strength at a given frequency and time. The Waterfall/Spectrogram view can help you identify the characteristics of the interference source, such as its frequency range, duty cycle, modulation type, and pattern. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 524; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 494.

What should be inspected to verify proper configuration is DNS. DNS stands for Domain Name System and is a service that resolves hostnames to IP addresses. In a controller-based AP deployment, DNS can be used to help the AP locate the controller by using a predefined hostname such as CISCO-CAPWAP-CONTROLLER or aruba-master. The AP sends a DNS query for this hostname and receives an IP address of the controller as a response. Therefore, if DNS is not configured properly or if there is no DNS entry for the controller hostname, the AP may not be able to locate the controller. NTP, BOOTP, and AP hosts file are not relevant for this scenario. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 374; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 364.

The string of characters and digits that is entered into an AP and a client STA for WPA2 security and is 8 characters long is called a passphrase. A passphrase is a human-readable text that is used to generate a Pre-Shared Key (PSK) for WPA2-Personal security. A passphrase can be between 8 and 63 characters long and can include any ASCII character. The PSK is a 256-bit key that is derived from the passphrase using a hashing algorithm called PBKDF2. The PSK is used to encrypt and decrypt the data frames between the AP and the client STA. A MSK is a Master Session Key that is generated by an authentication server for WPA2-Enterprise security. A WEP key is a 40-bit or 104-bit key that is used for Wired Equivalent Privacy (WEP) security, which is deprecated and insecure. A PSK is not a string of characters and digits, but a binary key. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 303; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 293.