Last Attempt XK0-005 Questions

The command that would ensure the server is set to runlevel 5 is systemct1 isolate graphical.target. This command will change the current target (or runlevel) of systemd to graphical.target, which is equivalent to runlevel 5 in SysV init systems. Graphical.target means that the system will start with a graphical user interface (GUI) and all services required for it.

The other options are not correct commands for setting the server to runlevel 5. The systemct1 isolate multi-user.target command will change the current target to multi-user.target, which is equivalent to runlevel 3 in SysV init systems. Multi-user.target means that the system will start with multiple user logins and networking, but without a GUI. The systemct1 isolate network.target command will change the current target to network.target, which is not a real runlevel but a synchronization point for network-related services. Network.target means that network functionality should be available, but does not specify whether it should be started before or after it. The systemct1 isolate basic.target command will change the current target to basic.target, which is also not a real runlevel but a synchronization point for basic system services. Basic.target means that all essential services should be started, but does not specify whether it should be started before or after it. References: systemd System and Service Manager; systemd.special(7) - Linux manual page

The filesystem that system logs are commonly stored in is /var. The /var filesystem is a directory that contains variable data files on Linux systems. Variable data files are files that are expected to grow in size over time, such as logs, caches, spools, and temporary files. The /var filesystem is separate from the / filesystem, which contains the essential system files, to prevent the / filesystem from being filled up by the variable data files. The system logs are files that record the events and activities of the system and its components, such as the kernel, the services, the applications, and the users. The system logs are useful for monitoring, troubleshooting, and auditing the system. The system logs are commonly stored in the /var/log directory, which is a subdirectory of the /var filesystem. The /var/log directory contains various log files, such as syslog, messages, dmesg, auth.log, and kern.log. The filesystem that system logs are commonly stored in is /var. This is the correct answer to the question. The other options are incorrect because they are not the filesystems that system logs are commonly stored in (/tmp, /etc, or /opt). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 16: Managing Logging and Monitoring, page 487.

The server’s firewall is preventing connections from being made, which is causing the connectivity issue. The output of iptables -L -n shows that the firewall is blocking all incoming traffic on port 22, which is the default port for SSH. The output of ssh -v user@104.21.75.76 shows that the connection is refused by the server. To resolve the issue, the administrator needs to allow port 22 on the firewall. The other options are incorrect because they are not supported by the outputs. The workstation has the correct IP settings, as shown by the output of ip addr show. The sshd service is enabled and running, as shown by the output of systemct1 status sshd. The server has the correct default gateway configuration, as shown by the output of ip route show. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 13: Managing Network Services, pages 406-407.

The most probable cause of the connectivity issue is that the network interface cable is not connected to a switch. This can be inferred from the output of the ip link list dev eth0 command, which shows that the network interface eth0 has the NO-CARRIER flag set. This flag indicates that there is no physical link detected on the interface, meaning that the cable is either unplugged or faulty. The other options are not valid causes of the issue. The address ac:00:11:22:33:cd is a valid Ethernet address, as it follows the format of six hexadecimal octets separated by colons. The Ethernet broadcast address should be ff:ff:ff:ff:ff:ff, which is the default value for all interfaces. The network interface eth0 is not using an old kernel module, as it shows the UP flag, which indicates that the interface is enabled and ready to transmit data. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 14: Managing Networking