Free CWAP-404 Questions Attempt

In a protocol analyzer, you would find an indication that a frame was transmitted as part of an A-MPDU by looking at the Aggregation flag in the Radio Tap Header. The Radio Tap Header is a pseudo-header that is added by some wireless capture devices to provide additional information about the physical layer characteristics of a frame. The Aggregation flag is one of the fields in this header, and it indicates whether the frame belongs to an A-MPDU or not. If the flag is set to 1, it means that the frame is part of an A-MPDU; if it is set to 0, it means that the frame is not part of an A-MPDU . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 9: PHY Layer Frame Formats andTechnologies, page 303; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 9: PHY Layer Frame Formats and Technologies, page 304.

An HE TB PPDU (High Efficiency Trigger-Based Packet Data Unit) is used to respond with an uplink transmission to an MU-RTS trigger frame in the 802.11ax PHY (Physical Layer). An MU-RTS trigger frame is a frame that initiates a multi-user transmission opportunity (MU-TXOP) by requesting multiple stations (STAs) to send clear-to-send (CTS) frames on different spatial streams or resource units (RUs). An HE TB PPDU is a frame that contains data from multiple STAs that have been allocated RUs by an MU-RTS trigger frame or another type of trigger frame. An HE SU PPDU (High Efficiency Single User Packet Data Unit) is a frame that contains data from a single STA using all available spatial streams or RUs. An HE MU PPDU (High Efficiency Multi User Packet Data Unit) is a frame that contains data from multiple STAs using different spatial streams or RUs without being triggered by another frame. A VHT PPDU (Very High Throughput Packet Data Unit) is a frame that uses the 802.11ac PHY and does not support multi-user transmissions.References:

• CWAP-404 Study Guide, Chapter 3: 802.11 MAC Layer Frame Formats and Technologies, page 101
• CWAP-404 Objectives, Section 3.4: Analyze multi-user transmissions
• CWAP-404 Study Guide, Chapter 3: 802.11 MAC Layer Frame Formats and Technologies, page 99

The difference between a Data frame and a QoS-Data frame is that QoS Data frames include a QoS control field. A Data frame is a type of data frame that is used to carry user data or upper layer protocol data between STAs and APs. A QoS Data frame is a type of data frame that is used to carry user data or upper layer protocol data between STAs and APs that support QoS (Quality of Service) features. QoS features allow different types of traffic to be prioritized and handled differently according to their QoS requirements, such as delay, jitter, throughput, etc. QoS Data frames include a QoS control field in their MAC header, which contains information such as traffic identifier (TID), queue size (TXOP), acknowledgment policy (ACK), etc., that are used for QoS purposes. The other options are not correct, as they do not describe the difference between Data and QoS Data frames. QoS Data frames do not include a DSCP (Differentiated Services Code Point) control field, which is part of the IP header in the network layer, not the MAC header in the data link layer. QoS Data frames do not include a QoS information element (IE), which is part of some management frames that indicate QoS capabilities or parameters, not data frames. QoS Data frames do not include an 802.1Q VLAN tag, which is part of some Ethernet frames that indicate VLAN membership or priority, not wireless frames. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 118-119

The configured Minimum Basic Rate (MBR) of a BSS can be identified by looking at the Supported Rates and Extended Supported Rates elements in a Beacon frame. A Beacon frame is a type of management frame that is transmitted by an AP to advertise its presence and capabilities to potential clients. A Beacon frame contains various information elements (IEs) that provide details about the BSS configuration and operation. The Supported Rates andExtended Supported Rates IEs list the data rates that are supported by the AP for data transmission. The MBR is the lowest data rate among these supported rates that is required for all clients to join and communicate with the BSS. The MBR is usually marked with a flag bit in these IEs to indicate its mandatory status. The other options are not correct, as they do not exist or do not indicate the MBR of a BSS. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 123-124