Leadership in Energy and Environmental Design (LEED) LEED-AP-BD+C Release Date

The Energy and Atmosphere Credit, Renewable Energy Production rewards projects that use renewable energy systems to offset building energy costs1. According to the LEED Reference Guide for Building Design and Construction2, the credit has two options: Option 1. On-Site Renewable Energy and Option 2. Off-Site Renewable Energy. Option 1 requires the project to use renewable energy systems that are located on the project site and that produce electricity or thermal energy for the project. The amount of renewable energy production is calculated based on the percentage of the annual energy cost that is offset by the renewable energy systems. Option 2 requires the project to use renewable energy systems that are located off the project site and that are owned by the project or have a long-term contract with the project. The amount of renewable energy production is calculated based on the percentage of the annual energy use that is offset by the renewable energy systems.

Therefore, among the given options, only Option D is relevant to the credit requirements, as it implies that the solar photovoltaic system is located on the project site and that the produced electricity is consumed by the project. The other options, such as carbon offsets, daylighting strategies, and passive solar strategies, are not directly related to the credit requirements, although they may have other benefits for the project.

References:

• Renewable Energy Production | U.S. Green Building Council
• LEED Reference Guide for Building Design and Construction v4
• Solar Photovoltaic Technology Basics | Department of Energy
• Photovoltaic system - Wikipedia

The strategy that will contribute toward the Interior Cross-Contamination Prevention strategy in Indoor Environmental Quality Credit, Enhanced Indoor Air Quality Strategies is to provide a ventilation system specifically for the laundry facility that has no recirculating air. This is because the laundry facility is a space where hazardous gases or chemicals may be present or used, such as detergents, bleach, or fabric softeners. According to the LEED v4 Reference Guide for Building Design and Construction, the project must "sufficiently exhaust each space where hazardous gases or chemicals may be present or used (e.g., garages, housekeeping and laundry areas, copying and printing rooms), using the exhaust rates determined in EQ Prerequisite Minimum Indoor Air Quality Performance or a minimum of 0.50 cfm per square foot (2.54 l/s per square meter), to create negative pressure with respect to adjacent spaces when the doors to the room are closed.For each of these spaces, provide self-closing doors and deck-to-deck partitions or a hard-lid ceiling."1Therefore, option D is the correct answer. The other options will not prevent cross-contamination from the laundry facility to the locker rooms. Relocating the laundry facility to the basement (option A) may reduce the exposure of the occupants to the laundry chemicals, but it will not eliminate the possibility of cross-contamination to other spaces in the basement. Naturally ventilating the laundry space per ASHRAE 62.1-2010 (option B) may not provide sufficient exhaust to create negative pressure and prevent cross-contamination, especially if the outdoor air quality is poor or the natural ventilation is not well designed. Installing particle filters, with a MERV of 13 or higher or F7 (option C) may improve the air quality in the laundry space, but it will not prevent the hazardous gases or chemicals from escaping to the adjacent spaces through the ventilation system or the gaps in the doors or ceiling.References: LEED v4 Reference Guide for Building Design and Construction, p.6881; ASHRAE Standard 62.1-2010, Section 6.2.52

According to the LEED v4 Reference Guide for Building Design and Construction, the discovery phase of energy-related systems should identify ventilation rates, along withother factors such as building orientation, envelope attributes, lighting levels, plug and process loads, and programmatic and operational parameters1.These factors should be used to create a preliminary “simple box” energy model to evaluate the energy performance of the building and explore potential strategies to reduce energy use1. The other options are not relevant for the discovery phase of energy-related systems.Functional performance tests are part of the implementation phase1.Thermal comfort ranges are related to indoor environmental quality2.Transportation options are related to sustainable sites3.References: IP Credit Integrative Process, LEED v4 Reference Guide for Building Design and Construction4123